How To Make A Ribbon Wreath With A Wire Hanger

Larn how to make this simple DIY ribbon wreath. Perfect for the holidays or whatsoever special occasion.

They look beautiful hanging on a front door or sitting equally a centerpiece of a dining room table with candles in the center. There'due south many options for sizes too as fashion and colors of ribbon. This DIY craft is fun for the whole family or a girlfriends get together. So grab your supplies and lets get crafting!

Video for how to make a ribbon wreath

[embedyt] https://www.youtube.com/spotter?v=DKhMDuXnSFc[/embedyt]

How to make a simple ribbon wreath

Supplies for making a ribbon wreath

1. Wire wreath frame (pictured to a higher place).  Commonly located in the floral department of any craft store or amazon, these come up in an array of sizes (4"-24"). Determine where you'll be wanting to utilise/hang  this wreath and size accordingly. For case, if you accept a big front door or entry, consider using a larger sized frame. If yous'd prefer to make a couple for tabular array centerpieces, perchance utilize a smaller frame. Information technology really simply depends. When you visit your local craft supply store, you'll exist able to run into the sizes and gauge more accordingly.
2. Floral pics. These aren't necessary to complete this project. They just add another element of character and dimension.
3. Ribbon. The style, color, and width of ribbon are upwards to y'all. I adopt ribbon that has a wired border. This makes it easier to motility, bend and guide the ribbon to where yous want it to be. I have fabricated this with a burlap ribbon that did not have a wired border and it turned out fine. I did observe that I used more ribbon than I normally would though. Typically, the larger the ribbon, the less you'll need. If you decide that you desire the ribbon to have tighter curls and a lot more of them, the more ribbon you'll need. If you lot prefer the curls to exist tighter and sit closer to the frame, the less you lot'll demand. It really just depends on what look you're going for. Watch the tutorial video before heading to the store for supplies. (Tip-when ownership ribbon, particularly if your arts and crafts store doesn't have a lot left of a particular color and style you are going for, buy extra! It'due south better to have too much than not plenty).
4. Wreath hanger. If yous are planning on hanging this on your front door, be sure yous have a wreath hanger to hang it from. I'll put a link below to the one we have.

Instructions for making a simple DIY ribbon wreath

1. Purchase supplies needed to complete projection (encounter listing higher up). Sentry tutorial to all-time gauge how much ribbon y'all may need. Better to take too much ribbon than non enough ( I can't stress this plenty).
2. Remove all excess packaging from ribbon and floral pics and wire frame.
3. With the wire frame arch facing down towards your work surface, tie a knot effectually and onto the 2 center wires of the wreath frame. If you are using a wired ribbon, you don't need to double knot it. But be sure that you get out a tail of at to the lowest degree an inch. If you are using a non-wired ribbon, I'd recommend a double knot. Just to exist certain that its secured and won't come undone.
4. Once your knot is secure, flip the frame over on the work surface so the knot is downwards (touching the work surface) and the curvation of the frame is now facing upward. Pull the tail of the ribbon up through the frame and then information technology won't exist visible from the underside. This is not a big deal if you only want to leave it. You won't see information technology anyhow since it will be on the back. This is merely how I prefer to practice mine and go on information technology dainty and make clean.
5. Having the wreath frame now facing up, y'all can begin construction.  With the within or the exterior channel (no information technology really doesn't matter), pull up a loop of ribbon the desired size (the loops of ribbon I did for this project were 3.5" and the ribbon was iv" broad-for reference). You'll want to effort and make each ane close to the same size. Perfection, however, isn't at all necessary. (If you'd prefer to add more dimension, you lot can also make some of the loops larger. Again, this is entirely up to you and its really customizable for each person. Practice whatever yous think will look good). See detailed pictures at lesser of post likewise.
   

(a moving picture for reference)

Pull upwardly desired size loop of ribbon either through the outside or inside channel of wire frame, and agree in place with your fingers. On the underside of the frame, twist the ribbon once or twice.

At present have the ribbon (while belongings the loop you previously made in identify) and pull up another loop of ribbon of similar size in a different aqueduct-within, centre or outside. Just not up the same     aqueduct previously washed.

Go on y'all this aforementioned pattern through the entire wreath frame. I discover that working in an "Southward" shape design works the all-time for me. Run across Picture below.

(this is only an instance of the "snaking or S" pattern I use when constructing then wreath. There volition be no gaps in the wreath as you'll button the loops of ribbon together)

While pulling up loops of ribbon, make certain to push the ribbon loops together after each twist and the beginning of each new loop. This volition proceed the loops shut and the wire frame curtained. You can make the wreath as dense with ribbon loops as you'd similar. Again, the more dense the wreath, the more ribbon yous'll utilise. When yous complete a spool of ribbon and need to kickoff another, necktie off the completed ribbon spool onto the frame.

Flip the wreath over (like when y'all first started) and tie on the new ribbon onto the 2 center channels.

Pull the tail of the ribbon up through an adjacent channel and either cut or tuck the tail then it won't be visible from the top side of the wreath. You lot tin can e'er go back and do this step once your wreath is completed.

 Continue around the frame of the wreath until the desired fullness is achieved.

Decorate with floral pics and other accessories as desired. You can hang mini ornament flick frames with family pictures, Christmas ornaments of assorted types and sizes. Theres really and then many options to customize this wreath. So have fun with it! Recollect, y'all can always take the ribbon out and start again if you really don't like it. Its not permanent-and then simply let your creative juices flow.

Hang wreath on forepart door using a wreath hanger or an extra length of ribbon to create a hanging loop.

Enjoy your creation for years to come!

(to brainstorm, from the lesser side of the wreath, tie the ribbon to the center two metallic bars)

(the under side of the wreath. Twist in one case or twice before threading ribbon upward through another aqueduct)

Underside of wreath. Don't worry if yours doesn't wait like this-nobody will see it.

Accept y'all fabricated a similar style DIY ribbon wreath and have any tips or tricks you'd similar to share?

Please post in the comments section below. I'd dear to know how you lot've made these beautiful wreaths. What's your favorite type of ribbon to use?

Shop this post

Disclosure: Some of the links below are affiliate links, meaning, at no additional cost to you lot, I volition earn a committee if y'all click through and make a buy.

• Antler Wreath hanger
• 12" wire wreath frame
• xiv" wire wreath frame
• 18" wire wreath frame
• Blackness & white buffalo cheque ribbon 2.five"
• Ruby & black buffalo check wire ribbon two.five"
• Holiday floral picks (optional)

Pin it for later:

I hope you all enjoyed making your wreath. Happy holidays.

Reader Interactions

Source: https://homemadeonourhomestead.com/how-to-make-a-ribbon-wreath/

Posted by: watsontaknoyse.blogspot.com

Share this post